diff --git a/.gitignore b/.gitignore
index 1cf796a..1fb1b54 100644
--- a/.gitignore
+++ b/.gitignore
@@ -51,4 +51,7 @@ LineIDs.dbg.bak
 *.suo
 
 # Own Ignores
-commit.txt
\ No newline at end of file
+commit.txt
+*.txt
+*.exe
+*.xlsx
\ No newline at end of file
diff --git a/liste_alarme.md b/liste_alarme.md
new file mode 100644
index 0000000..51227d0
--- /dev/null
+++ b/liste_alarme.md
@@ -0,0 +1,67 @@
+# List der Alarme
+
+Notiz: Die Aktuelle Schnittstelle ist noch nicht definiert, daher ist dies nur als Entwurf zu werten.
+
+## Kategorien
+
+Kat_1 -> Fehler
+Kat_2 -> Manueller Eingriff
+Kat_3 -> Warnung
+Kat_4 -> Info Messages
+
+
+## Liste Fehler
+
+- 1.01 {unit_descr}: Pressure difference segment inlet to big
+- 1.02 {unit_descr}: DC main switch not closed
+- 1.03 {unit_descr}: Leakage in double segment 1 and 2
+- 1.04 {unit_descr}: Leakage in double segment 3 and 4
+- 1.05 {unit_descr}: Leakage in tank
+- 1.06 {unit_descr}: EtherCAT communication error
+- 1.07 {unit_descr}: Isolation Error
+- 1.08 {unit_descr}: Units out of balance
+- 1.09 {unit_descr}: Modules out of balance
+- 1.10 {unit_descr} Inverter startup timeout
+- 1.11 Emergency stop not ok
+- 1.12 {unit_descr}: EtherCAT communication error
+- 1.13 {unit_descr}: Safetyinterlock reset timeout
+- 1.14 {unit_descr} Inverter over temperature
+- 1.15 {unit_descr} Inverter AC over voltage
+- 1.16 {unit_descr} Inverter AC under voltage
+- 1.17 {unit_descr} Inverter DC over voltage
+- 1.18 {unit_descr} Inverter over frequency
+- 1.19 {unit_descr} Inverter under frequency
+- 1.20 {unit_descr} Inverter ground fault
+- 1.21 {unit_descr} Inverter internal error
+- 1.22 {unit_descr}: Inverter Error
+- 1.23 Valve {unit_descr + sensor detail} did not open -> Bezogen auf valves
+- 1.24 Valve {unit_descr + sensor detail} did not close -> Bezogen auf valves
+- 1.25 Valve {unit_descr + sensor detail} feedback open circuit -> Bezogen auf valves
+- 1.26 Valve {unit_descr + sensor detail} setpoint open circuit -> Bezogen auf valves
+- 1.27 Valve {unit_descr + sensor detail} not in range
+- 1.28 {unit_descr + sensor detail} input open circuit -> Bezogen auf Analog Input werte
+- 1.29 Analog Input {unit_descr + sensor detail} card error
+- 1.30 Analog Input {unit_descr + sensor detail} short circuit
+- 1.31 Analog Input {unit_descr + sensor detail} configuration error
+- 1.32 Analog Input {unit_descr + sensor detail}: Input Value below error limit ({limit})
+- 1.33 Analog Input {unit_descr + sensor detail}: Input Value above error limit ({1})
+- 1.34 Analog output {unit_descr + sensor detail} config error -> Bezogen auf Analog Output werte
+- 1.35 Motor {unit_descr + sensor detail} repair switch open
+- 1.36 Motor {unit_descr + sensor detail} not in target
+
+## Liste Manueller Eingriff
+
+- 2.01 Notaus {bereich} Betätigt
+
+
+## List Warnungen
+- 3.01 Not all components in automatic mode
+- 3.02 {unit_descr}: Safetyinterlocks active
+- 3.03 Analog Input {unit_descr + sensor detail}: Input Value below warning limit ({1})
+- 3.04 Analog Input {unit_descr + sensor detail}: Input Value above warning limit ({1})
+
+## Liste Info Messages
+- 4.01 Battery full
+- 4.02 Battery empty
+- 4.03 {unit_descr}: Shutdown discharge stopped because of low dc voltage
+- 4.04 {unit_descr}: Shutdown discharge stopped because of unit voltage level